exwein
Full Member | Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
v0.4a
Drive: 1(ATA)
Model: KINGSTON SV300S37A60G
Fw : 541ABBF0
Size : 57241 MB
--- SandForce specific ---
Signature : 138-0-27438
HW Revision : 500026BB (B04)
Try to unlock the drive (default)...
Drive unlocked (default)!
FW : [541ABBF0 ]
FW string : [B:FW_PPRO_540_20140114_739675:FW_PPRO_5_4_1_Release-742748 ]
Config file : [cfg/cfg_MLC_MIC_64Gb_MT29F64G08CBABBWP_2Q_1C_1D ]
ROM Revision: [400 ]
NAND ID : 0x2c, 0x64, 0x44, 0x4b, 0xa9, 0x0, 0x0, 0x0
Page Size : 8936
NAND CE : 1
Sector/Page : 8
Die/CE : 1
Block/Die : 2048
Page/Block : 256
Raw Size : 134217728
NAND Max EC : 3000
Max PE Cycles : 3000
Cur PE Cycles : 89
Life In Seconds : 0 (Not Set)
LBA Size : 117231408
Sector Size : 512
Sector Align : +0
NAND ID : 0x2c,0x64
Serial Output Control : Default(Off)
Erase R Block : Disable
Panic Handling Enabled : Disable
Panic On SATA Error : Disable
Write Throttling Test Mode: Disable
R.A.I.S.E. : Disable
Flash CE : 8
Bank00: 0x2c,0x64,0x44,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank01: 0x2c,0x64,0x44,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank02: 0x2c,0x64,0x44,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank03: 0x2c,0x64,0x44,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank04: 0x2c,0x64,0x44,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank05: 0x2c,0x64,0x44,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank06: 0x2c,0x64,0x44,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank07: 0x2c,0x64,0x44,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Led Settings
Activity LED Polarity : 0 (Normal)
Fault LED Polarity : 0 (Normal)
LED Blink Rate : 0 (250ms)
Power Managment Settings
Power Management Version : 2 (B01)
Active State Power Mode : 0 (Default)
DIPM Behavior in Active State : 0 (Default)
HIPM Behavior in Active State : 0 (Default)
Auto Idle Enable : 0 (Default)
Idle State Power Mode : 0 (Default)
DIPM Behavior in Idle State : 0 (Default)
HIPM Behavior in Idle State : 0 (Default)
Standby State Power Mode : 0 (Default)
DIPM Behavior in Standby State : 0 (Default)
HIPM Behavior in Standby State : 0 (Default)
Sleep State Power Mode : 0 (Default)
DIPM Behavior in Sleep State : 0 (Default)
HIPM Behavior in Sleep State : 0 (Default)
Auto slumber timer : 0
CMU power down : 0 (Default)
Dual-align BIST Feature : 0 (Default)
Temperature Sensor Settings
Sensor 1:
Device ID : 2 (LM73)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 70
Max Temperature Threshold Level 2 Entry Point (MT2) : 85
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 2 (Temperature Threshold Event Log)
Max Temperature Threshold Behavior for MT2 (MT2B) : 2 (Temperature Threshold Event Log)
Min Temperature Threshold Behavior (LT1B) : 2 (Temperature Threshold Event Log)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Sensor 2:
Device ID : 0 (Default)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0
Max Temperature Threshold Level 2 Entry Point (MT2) : 0
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Security Erase Options
Security Erase Behavior : 2 (Expanded)
Enhanced Security Erase Behavior (Military Erase) : 0 (Default)
SATA Command and Firmware Options
Flush Cache Behavior : 0 (Default)
ATA Security Set Enable : 1 (Off)
Spread Spectrum Clocking Enable : 0 (Default)
SATA Link Handling on Reboot : 0 (Default)
ACS2 Support : 0 (Default)
Failed Secure Unlock Delay Enable : 0 (Default(No delay))
Seek Complete in Error Status : 0 (Default)
Read Long with Retry and without Retry : 0 (Default)
Read Sectors without Retry : 0 (Default)
Write DMA without Retry : 0 (Default)
Write Long with Retry and without Retry : 0 (Default)
Max SATA Link Rate : 0 (Default)
Deterministic Trim Setting : 0 (Default)
Controller Drive Strength Rate : 0 (Default)
PHY Setting : 0 (Default)
Controller Slew Rate : 0 (Default)
Put SIG FIS Delay : 0 (Default)
Set Multiple Handling : 0 (Default)
TRIM Timer Abort : 0 (Enable(Default))
Trim Support/Setting Word 169 Bit 0 : 0 (Default(Firmware default setting))
RDD1 Optimization : 0 (Default)
Security Unlock Drive : 0 (Default(Compare Master Password))
Power Throttling Options
Average Power Level 0-100 : 0
Maximum Power Level 0-100 : 0
Power Throttling Upon Unsafe Shutdown : 0 (Default)
Dynamic Read Scrub
Read Scrub Enabled : 0 (Default (Enabled))
Dynamic Read Scrub End Range1 : 0
Dynamic Read Scrub Rate Range1 : 0
Dynamic Read Scrub End Range2 : 0
Dynamic Read Scrub Rate Range2 : 0
Dynamic Read Scrub End Range3 : 0
Dynamic Read Scrub Rate Range3 : 0
Dynamic Read Scrub End Range4 : 0
Dynamic Read Scrub Rate Range4 : 0
Low Level Format Settings
Max LBA Count for 512B Sectors : 117231408
Max LBA Count for 512B Plus DIFF Sectors : 0
Max LBA Count for 520B Sectors : 0
Max LBA Count for 524B : 0
Max LBA Count for 528B : 0
Max LBA Count for 4096 Sectors : 0
Max LBA Count for 4096 Plus DIFF Sectors : 0
Host Protected Area
Host Protected Access : 0 (Always Reset HPA State On COMRESET)
End of Life Behavior
Enable End of Life : 0 (Default (EOL Enabled))
EOL Threshold 1 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Light Write Throttling))
EOL Threshold 2 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Heavy Write Throttling))
CDU Smart settings: defined 2 attributes
## Attr IntId Tresh Flag
00 0xeb 0x00 0 0x00
01 0xbd 0x12 0 0x00
Fab Defect list entry : 0
User Defect list entry: 0
Panic Dumps : 0
Panic Dumps list:
Idx Accurev SyncCode UnlockLevel Size DataSize EPA Log Ok CRC Ok
0 -1 0xffffffff 0xffffffff -1 -1 0x00020002 0x0000 0x0000
1 -1 0xffffffff 0xffffffff -1 -1 0x20020002 0x0000 0x0000
2 -1 0xffffffff 0xffffffff -1 -1 0x00028002 0x0000 0x0000
3 -1 0xffffffff 0xffffffff -1 -1 0x20028002 0x0000 0x0000
MST settings not exist.
MST result:
Format Version : 4
Test State : Not Activated
Input Offset : 16
Current Command : Write
Cycles Required : 20
Cycles Complete : 20
ElapsedTime : 24385
StartTemperature : 31
MaxTemperature : 63
Grown Bad Block : 0
Errors:
Program : 0
Correctable RAISE : 0
Uncorrectable RAISE: 0
Erase : 0
Unintended Erase : 0
Upper Page Program : 0
Lower Page Program : 0
0_Bit : 2248809397 84.03%
1_Bit : 369890942 13.82%
2_Bit : 50856718 1.90%
3_Bit : 5916404 0.22%
4_Bit : 607706 0.02%
5_Bit : 58342
6_Bit : 5558
7_Bit : 511
8_Bit : 67
9_Bit : 9
10_Bit : 1
|
