Alekslyas
Newbie | Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору wlo, с Вашей помощью продвинулся дальше!! но получил новую ошибку FATAL_ERROR: Could not perform the FORMAT() operation on the drive... На форуме ранее прочитал что люди сталкивались с такой проблемой но решение не описано. Возможно неправильная конфигурация подобрана ? [Alex@Fedora-1486 ~]$ su - Пароль: [root@Fedora-1486 ~]# lsscsi [3:0:0:0] disk ATA Maxtor 6V200E0 VA11 /dev/sda [5:0:0:0] disk ATA SandForce{200026 402A /dev/sdb [8:0:0:0] disk Multi Flash Reader 1.00 /dev/sdc [root@Fedora-1486 ~]# sg_map /dev/sg0 /dev/sda /dev/sg1 /dev/sdb /dev/sg2 /dev/sdc [root@Fedora-1486 ~]# /home/Alex/SF_Genesis -PROCESS_SSD 5:0:0:0 /home/Alex/FW_PPRO_5_8_2_Release.906190.release.0.mfp /home/Alex/22983.0.driveconfig 2345 www_123 log=/home/Alex/fw.log ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit SF_Core Library: v1.7.1.20130612-fc14-32bit Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [Thu 02/08/2018 17:59:16] - SF_Genesis has been invoked with the following parameters: ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ argv[1]: -PROCESS_SSD argv[2]: 5:0:0:0 argv[3]: /home/Alex/FW_PPRO_5_8_2_Release.906190.release.0.mfp argv[4]: /home/Alex/22983.0.driveconfig argv[5]: 2345 argv[6]: www_123 argv[7]: log=/home/Alex/fw.log ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [Thu 02/08/2018 17:59:16] - Instructing the operating system to purge any existing cached data for device: '5:0:0:0' [Thu 02/08/2018 17:59:21] - Issuing a discovery command for device: '5:0:0:0' [Thu 02/08/2018 17:59:26] - Discovery command completed... [Thu 02/08/2018 17:59:26] - Waiting 5 seconds for the system to settle... [Thu 02/08/2018 17:59:31] - Device designation string '5:0:0:0' is mapped to node '/dev/sg1' [Thu 02/08/2018 17:59:31] - Proceeding to process SSD device with the following parameters: ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ DeviceName = /dev/sg1 MFP Package Filename = /home/Alex/FW_PPRO_5_8_2_Release.906190.release.0.mfp Configuration File = /home/Alex/22983.0.driveconfig Serial No. = 2345 World Wide Name = www_123 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [Thu 02/08/2018 17:59:31] - Successfully received the IDENTIFY data from the drive... [Thu 02/08/2018 17:59:31] - Validating Manufacturing Firmware Package: /home/Alex/FW_PPRO_5_8_2_Release.906190.release.0.mfp [Thu 02/08/2018 17:59:31] - Successfully opened the package: /home/Alex/FW_PPRO_5_8_2_Release.906190.release.0.mfp [Thu 02/08/2018 17:59:31] - file /home/Alex/22983.0.driveconfig Loaded successfully [Thu 02/08/2018 17:59:31] - Warning: Unable to query diagnostics information to perform power management settings check [Thu 02/08/2018 17:59:31] - B01 Power Management configuration request detected [Thu 02/08/2018 17:59:31] - Successfully extracted *.DriveConfig file: /home/Alex/22983.0.driveconfig [Thu 02/08/2018 17:59:31] - Extracted Config_ID: 1 (22983) in DriveConfig file: /home/Alex/22983.0.driveconfig [Thu 02/08/2018 17:59:31] - Extracted SerialOutputControl: 0 [Thu 02/08/2018 17:59:31] - Searching for flashware image for configuration 22983 [Thu 02/08/2018 17:59:31] - Manifest found for configuration 22983 [Thu 02/08/2018 17:59:31] - Flashware image extracted: 22983_fw_cl_mlc_Intel_64Gb_JS29F64G08ACME3_2Q_1C_1D_PP_R00946_s512.vic [Thu 02/08/2018 17:59:31] - Searching for manufacturing image for configuration 22983 [Thu 02/08/2018 17:59:31] - Manifest found for configuration 22983 [Thu 02/08/2018 17:59:31] - Manufacturing image extracted: 22983_mf_mlc_Intel_64Gb_JS29F64G08ACME3_2Q_1C_1D_PP_R00946_s512.vic [Thu 02/08/2018 17:59:31] - Proceeding in ROM mode, download feature 3... [Thu 02/08/2018 17:59:32] - Successfully downloaded MFB to the drive... [Thu 02/08/2018 17:59:32] - Waiting (5 sec) for the drive to settle... [Thu 02/08/2018 17:59:37] - Successfully received the IDENTIFY data from the drive... [Thu 02/08/2018 17:59:37] - Firmware revision reported to be: '582ABBM0'. This indicates MFB download was successful. [Thu 02/08/2018 17:59:37] - Successfully enabled SMART capabilities... [Thu 02/08/2018 17:59:39] - Successfully issued a diagnostic unlock... [Thu 02/08/2018 17:59:40] - Performing the flash test of block 0 (0x0000)... [Thu 02/08/2018 17:59:42] - Flash Test Results: ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ----------------------------------------------------------------------------- Flash Test Parameters: ----------------------------------------------------------------------------- Block Count: 0 Page Count: 1 Bus Count: 2 Chip Enabled Count: 1 Die Count: 1 Lane Count: 4 Plane Count: 2 ----------------------------------------------------------------------------- Results Notes: ----------------------- N1 - At least one page tested and passed with no bit errors. N2 - No test data available. Test may have aborted, or failed during the testing. N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power. N4 - At least one erased page tested had bit error rate greater than half the correction power. N5 - Walking zeros test failed. N6 - Walking ones test failed. N7 - Block contained factory bad block markings and testing was skipped. N8 - At least one page tested and had bit error rate greater than the correction power on plane 0. N9 - Block in plane 0 was marked as a factory bad block. N10 - At least one page tested and had bit error rate greater than the correction power on plane 1. N11 - Block in plane 1 was marked as a factory bad block. ----------------------------------------------------------------------------- +------+------+------+------+--------+--------------------------------------------+---------+ | Bus | CE | Die | Lane | Value | Result Notes | Overall | +------+------+------+------+--------+--------------------------------------------+---------+ | 0 | 0 | 0 | 0 | 0x0002 | N3 | WARNING | +------+------+------+------+--------+--------------------------------------------+---------+ | 0 | 0 | 0 | 1 | 0x0002 | N3 | WARNING | +------+------+------+------+--------+--------------------------------------------+---------+ | 0 | 0 | 0 | 2 | 0x0002 | N3 | WARNING | +------+------+------+------+--------+--------------------------------------------+---------+ | 0 | 0 | 0 | 3 | 0x0002 | N3 | WARNING | +------+------+------+------+--------+--------------------------------------------+---------+ | 1 | 0 | 0 | 0 | 0x0002 | N3 | WARNING | +------+------+------+------+--------+--------------------------------------------+---------+ | 1 | 0 | 0 | 1 | 0x0022 | N3,N5 | WARNING | +------+------+------+------+--------+--------------------------------------------+---------+ | 1 | 0 | 0 | 2 | 0x0002 | N3 | WARNING | +------+------+------+------+--------+--------------------------------------------+---------+ | 1 | 0 | 0 | 3 | 0x0002 | N3 | WARNING | +------+------+------+------+--------+--------------------------------------------+---------+ ----------------------------------------------------------------------------- Total Number of test results: 8 Number of failures: 0 Number of Passed with warnings: 8 No. Passed without warnings: 0 ----------------------------------------------------------------------------- ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [Thu 02/08/2018 17:59:42] - Performing the FORMAT Command with the following parameters: ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ MemoryWearCycleCapability = 0 CurrentPE_CycleCount = 0 LifeInSeconds = 0 LogicalCapacity = 125045424 SectorSize = 512 SectorAlignmentOffset = 0 ExpectedMemoryID = 34953 (0x8889) ExpectedNumDies = 0 SerialOutputControl = 0 Time[8] = 0x0000000000000000 MiscFlag_Erase_R_Block = 0 MiscFlag_PanicHandlingEnabled = 0 MiscFlag_PanicOnSATA_Error = 0 MiscFlag_WriteThrottlingTestMode = 0 MiscFlag_DisableUserBandECCX = 1 L_PageSize = 0 E_PageSize = 0 ErrorCorrectionPower = 0 ConfigDeviceReadDisturbCount = 0 ConfigDeviceReadDisturbCountLow = 0 ExtraOptions_0_1 = 0 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [Thu 02/08/2018 18:00:02] - FATAL_ERROR: Could not perform the FORMAT() operation on the drive... (0x0000C048:SF_SCT (C048h): Root Creation Failed (MFB format)) [Thu 02/08/2018 18:00:02] - End of Genesis manufacturing log. [Thu 02/08/2018 18:00:02] - Exiting... [Thu 02/08/2018 18:00:02] - Overall Result for Device: /dev/sg1 ****** FAIL ****** Добавлено: Работает и в режиме IDE. Проверено. | Всего записей: 28 | Зарегистр. 31-05-2006 | Отправлено: 19:05 08-02-2018 | Исправлено: Alekslyas, 19:17 08-02-2018 |
|