ikinn77
Newbie | Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
v0.43a
Drive: 0(ATA)
Model: SPCC Solid State Disk
Fw : 606ABBF0
Size : 114472 MB
--- SandForce specific ---
Signature : 190-0-22800
HW Revision : 500026BB (B04)
Try to unlock the drive (default)...
Drive unlocked (default)!
FW : [606ABBF0 ]
FW string : [B:FW_PPRO_5_6_1_20140326_836378:FW_PPRO_6_0_6_Release-1084341 ]
Config file : [cfg/cfg_eMLC_Intel_64Gb_PF29F16B16MCME1_2Q_2C_1D ]
ROM Revision: [400 ]
NAND ID : 0x89, 0x88, 0x24, 0x4b, 0xa9, 0x0, 0x0, 0x0
Page Size : 8640
NAND CE : 2
Sector/Page : 8
Die/CE : 1
Block/Die : 2048
Page/Block : 256
Raw Size : 268435456
NAND Max EC : 10000
Max PE Cycles : 10000
Cur PE Cycles : 1
Life In Seconds : 157680000 (5 year warranty)
LBA Size : 234441648
Sector Size : 512
Sector Align : +0
NAND ID : 0x89,0x88
Serial Output Control : Enable Bad Block Output
Erase R Block : Disable
Panic Handling Enabled : Disable
Panic On SATA Error : Disable
Write Throttling Test Mode: Disable
R.A.I.S.E. : Enable
Flash CE : 16
Bank00: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank01: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank02: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank03: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank04: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank05: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank06: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank07: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank08: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank09: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank10: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank11: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank12: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank13: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank14: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank15: 0x89,0x88,0x24,0x4b,0xa9,0x0,0x0,0x0 - Intel 25nm(L74A) MLC 64Gb/CE 64Gb/die
UART freq : 0
SATA Status Coalesting : 0
Compressible data performance tuning option : 0 (no tuning for compr. data)
Serial Output Control : 0 (Default)
Write Speed Limit : 0 (Off)
Led Settings
Activity LED Polarity : 0 (Normal)
Fault LED Polarity : 0 (Normal)
LED Blink Rate : 0 (250ms)
Power Managment Settings
Power Management Version : 2 (B01)
Active State Power Mode : 0 (Default)
DIPM Behavior in Active State : 0 (Default)
HIPM Behavior in Active State : 0 (Default)
Auto Idle Enable : 0 (Default)
Idle State Power Mode : 0 (Default)
DIPM Behavior in Idle State : 0 (Default)
HIPM Behavior in Idle State : 0 (Default)
Standby State Power Mode : 0 (Default)
DIPM Behavior in Standby State : 0 (Default)
HIPM Behavior in Standby State : 0 (Default)
Sleep State Power Mode : 0 (Default)
DIPM Behavior in Sleep State : 0 (Default)
HIPM Behavior in Sleep State : 0 (Default)
Auto slumber timer : 0
CMU power down : 0 (Default)
Dual-align BIST Feature : 0 (Default)
Temperature Sensor Settings
Sensor 1:
Device ID : 255 (Disabled)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0n (Default - 65C)
Max Temperature Threshold Level 2 Entry Point (MT2) : 0n (Default - 70C)
Min Temperature Threshold (LT1) : 0n (Default - 0C)
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0 (Default - MT1)
Sensor 2:
Device ID : 255 (Disabled)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0
Max Temperature Threshold Level 2 Entry Point (MT2) : 0
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Security Erase Options
Security Erase Behavior : 0 (Default)
Enhanced Security Erase Behavior (Military Erase) : 0 (Default)
SATA Command and Firmware Options
Flush Cache Behavior : 0 (Default)
ATA Security Set Enable : 0 (Default)
Spread Spectrum Clocking Enable : 0 (Default)
SATA Link Handling on Reboot : 0 (Default)
ACS2 Support : 0 (Default)
Failed Secure Unlock Delay Enable : 0 (Default(No delay))
Seek Complete in Error Status : 0 (Default)
Read Long with Retry and without Retry : 0 (Default)
Read Sectors without Retry : 0 (Default)
Write DMA without Retry : 0 (Default)
Write Long with Retry and without Retry : 0 (Default)
Max SATA Link Rate : 0 (Default)
Deterministic Trim Setting : 0 (Default)
Controller Drive Strength Rate : 0 (Default)
PHY Setting : 0 (Default)
Controller Slew Rate : 0 (Default)
Put SIG FIS Delay : 0 (Default)
Set Multiple Handling : 0 (Default)
TRIM Timer Abort : 0 (Enable(Default))
Trim Support/Setting Word 169 Bit 0 : 0 (Default(Firmware default setting))
RDD1 Optimization : 0 (Default)
Security Unlock Drive : 0 (Default(Compare Master Password))
Power Throttling Options
Average Power Level 0-100 : 0
Maximum Power Level 0-100 : 0
Power Throttling Upon Unsafe Shutdown : 0 (Default)
Dynamic Read Scrub
Read Scrub Enabled : 0 (Default (Enabled))
Dynamic Read Scrub End Range1 : 0
Dynamic Read Scrub Rate Range1 : 0
Dynamic Read Scrub End Range2 : 0
Dynamic Read Scrub Rate Range2 : 0
Dynamic Read Scrub End Range3 : 0
Dynamic Read Scrub Rate Range3 : 0
Dynamic Read Scrub End Range4 : 0
Dynamic Read Scrub Rate Range4 : 0
Low Level Format Settings
Number of entries in Max LBA Setting : 1
Sub-Sector Size [0] : 512
Pattern Size [0] : 2
Sub-Sector and Patterns per sector [0] : 0
Max LBA Count [0] : 234441648
Host Protected Area
Host Protected Access : 0 (Always Reset HPA State On COMRESET)
End of Life Behavior
Enable End of Life : 0 (Default (EOL Enabled))
EOL Threshold 1 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Light Write Throttling))
EOL Threshold 2 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Heavy Write Throttling))
CDU Smart settings: default
Fab Defect list entry : 9
Idx Bus CE Die Plane Block Lane3210 Defects
0 0 0 0 0 45 BBBB 4
1 1 0 0 0 45 BBBB 4
2 0 0 0 1 45 BBBB 4
3 1 0 0 1 45 BBBB 4
4 0 1 0 0 45 BBBB 4
5 1 1 0 0 45 BBBB 4
6 0 1 0 1 45 BBBB 4
7 1 1 0 1 45 BBBB 4
8 0 0 0 1 1010 _B__ 1
Fab Defects : 33
User Defect list entry: 0
Panic Dumps : 3
Panic Dumps list:
Idx Accurev SyncCode UnlockLevel Size DataSize EPA Log Ok CRC Ok
0 906190 0xe531a2fd 0xffffff00 3388 2956768 0x00020002 0x0001 0x0001
1 906190 0xe531a2fd 0xffffff00 3388 2956768 0x20020002 0x0001 0x0001
2 906190 0xe531a2fd 0xffffff00 3388 2956768 0x00020082 0x0001 0x0000
3 906190 0xe531a2fd 0xffffff00 3388 2956768 0x20020082 0x0001 0x0001
MST settings not exist.
MST result not exits. |
Всего записей: 5 | Зарегистр. 21-11-2009 | Отправлено: 17:29 11-03-2019 | Исправлено: ikinn77, 20:10 11-03-2019 |
|
