I_G_O_R
Newbie | Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
v0.4a
Drive: 3(ATA)
Model: Silicon_Power_V60-120Gb
Fw : 5.8.2
Size : 114473 MB
--- SandForce specific ---
Signature : 162-0-22321
HW Revision : 200026BB (B01)
Try to unlock the drive (01 02 03 04 05 06 07 08 09 00 01 02 03 04 05 06)...
Drive unlocked (01 02 03 04 05 06 07 08 09 00 01 02 03 04 05 06)!
FW : [582ABBF0 ]
FW string : [B:FW_PPRO_5_6_1_20140326_836378:FW_PPRO_5_8_2_Release-906190 ]
Config file : [cfg/cfg_MLC_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D ]
ROM Revision: [20D ]
NAND ID : 0x2c, 0x88, 0x4, 0x4b, 0xa9, 0x0, 0x0, 0x0
Page Size : 8640
NAND CE : 2
Sector/Page : 8
Die/CE : 1
Block/Die : 2048
Page/Block : 256
Raw Size : 268435456
NAND Max EC : 3000
Max PE Cycles : 3000
Cur PE Cycles : 0
Life In Seconds : 0 (Not Set)
LBA Size : 234441648
Sector Size : 512
Sector Align : +0
NAND ID : 0x2c,0x88
Serial Output Control : Default(Off)
Erase R Block : Disable
Panic Handling Enabled : Disable
Panic On SATA Error : Disable
Write Throttling Test Mode: Disable
R.A.I.S.E. : Enable
Flash CE : 16
Bank00: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank01: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank02: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank03: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank04: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank05: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank06: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank07: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank08: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank09: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank10: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank11: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank12: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank13: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank14: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Bank15: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 64Gb/die
Led Settings
Activity LED Polarity : 0 (Normal)
Fault LED Polarity : 0 (Normal)
LED Blink Rate : 0 (250ms)
Power Managment Settings
Power Management Version : 0 (Disable)
Temperature Sensor Settings
Sensor 1:
Device ID : 0 (Default)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0
Max Temperature Threshold Level 2 Entry Point (MT2) : 0
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Sensor 2:
Device ID : 0 (Default)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0
Max Temperature Threshold Level 2 Entry Point (MT2) : 0
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Security Erase Options
Security Erase Behavior : 0 (Default)
Enhanced Security Erase Behavior (Military Erase) : 0 (Default)
SATA Command and Firmware Options
Flush Cache Behavior : 0 (Default)
ATA Security Set Enable : 0 (Default)
Spread Spectrum Clocking Enable : 0 (Default)
SATA Link Handling on Reboot : 0 (Default)
ACS2 Support : 0 (Default)
Failed Secure Unlock Delay Enable : 0 (Default(No delay))
Seek Complete in Error Status : 0 (Default)
Read Long with Retry and without Retry : 0 (Default)
Read Sectors without Retry : 0 (Default)
Write DMA without Retry : 0 (Default)
Write Long with Retry and without Retry : 0 (Default)
Max SATA Link Rate : 0 (Default)
Deterministic Trim Setting : 0 (Default)
Controller Drive Strength Rate : 0 (Default)
PHY Setting : 0 (Default)
Controller Slew Rate : 0 (Default)
Put SIG FIS Delay : 0 (Default)
Set Multiple Handling : 0 (Default)
TRIM Timer Abort : 0 (Enable(Default))
Trim Support/Setting Word 169 Bit 0 : 0 (Default(Firmware default setting))
RDD1 Optimization : 0 (Default)
Security Unlock Drive : 0 (Default(Compare Master Password))
Power Throttling Options
Average Power Level 0-100 : 0
Maximum Power Level 0-100 : 0
Power Throttling Upon Unsafe Shutdown : 0 (Default)
Dynamic Read Scrub
Read Scrub Enabled : 0 (Default (Enabled))
Dynamic Read Scrub End Range1 : 0
Dynamic Read Scrub Rate Range1 : 0
Dynamic Read Scrub End Range2 : 0
Dynamic Read Scrub Rate Range2 : 0
Dynamic Read Scrub End Range3 : 0
Dynamic Read Scrub Rate Range3 : 0
Dynamic Read Scrub End Range4 : 0
Dynamic Read Scrub Rate Range4 : 0
Low Level Format Settings
Max LBA Count for 512B Sectors : 234441648
Max LBA Count for 512B Plus DIFF Sectors : 0
Max LBA Count for 520B Sectors : 0
Max LBA Count for 524B : 0
Max LBA Count for 528B : 0
Max LBA Count for 4096 Sectors : 0
Max LBA Count for 4096 Plus DIFF Sectors : 0
Host Protected Area
Host Protected Access : 0 (Always Reset HPA State On COMRESET)
End of Life Behavior
Enable End of Life : 0 (Default (EOL Enabled))
EOL Threshold 1 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Light Write Throttling))
EOL Threshold 2 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Heavy Write Throttling))
CDU Smart settings: default
Fab Defect list entry : 0
User Defect list entry: 0
Panic Dumps : 0
Panic Dumps list:
Idx Accurev SyncCode UnlockLevel Size DataSize EPA Log Ok CRC Ok
0 -1 0xffffffff 0xffffffff -1 -1 0x00020002 0x0000 0x0000
1 -1 0xffffffff 0xffffffff -1 -1 0x20020002 0x0000 0x0000
2 -1 0xffffffff 0xffffffff -1 -1 0x00020082 0x0000 0x0000
3 -1 0xffffffff 0xffffffff -1 -1 0x20020082 0x0000 0x0000
MST settings not exist.
MST result not exits. |
Всего записей: 25 | Зарегистр. 24-01-2005 | Отправлено: 18:37 23-10-2018 | Исправлено: I_G_O_R, 18:40 23-10-2018 |
|
