speedboy
Junior Member | Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору v0.4a Drive: 1(ATA) Model: OWC Mercury Electra 3G SSD Fw : 603ABBF0 Size : 457862 MB --- SandForce specific --- Signature : 154-1172-33025 HW Revision : 500026BB (B04) Try to unlock the drive (owc)... Drive unlocked (owc)! FW : [603ABBF0 ] FW string : [B:FW_PPRO_6_0_3_Release_1007955_20150128:FW_PPRO_6_0_3_9th_Release-1041030 ] Config file : [cfg/cfg_MLC_MIC_128Gb_MT29F256G08CECAB_2Q_4C_1D_S ] ROM Revision: [400 ] NAND ID : 0x2c, 0x84, 0x64, 0x3c, 0xa5, 0x0, 0x0, 0x0 Page Size : 17600 NAND CE : 4 Sector/Page : 16 Die/CE : 1 Block/Die : 1024 Page/Block : 512 Raw Size : 1073741824 NAND Max EC : 3000 Max PE Cycles : 3000 Cur PE Cycles : 50 Life In Seconds : 0 (Not Set) LBA Size : 937703088 Sector Size : 512 Sector Align : +0 NAND ID : 0x2c,0x84 Serial Output Control : Enable Bad Block Output Erase R Block : Disable Panic Handling Enabled : Disable Panic On SATA Error : Disable Write Throttling Test Mode: Disable R.A.I.S.E. : Enable Flash CE : 32 Bank00: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank01: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank02: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank03: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank04: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank05: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank06: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank07: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank08: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank09: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank10: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank11: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank12: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank13: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank14: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank15: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank16: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank17: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank18: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank19: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank20: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank21: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank22: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank23: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank24: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank25: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank26: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank27: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank28: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank29: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank30: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Bank31: 0x2c,0x84,0x64,0x3c,0xa5,0x0,0x0,0x0 - Micron MLC 128Gb/CE 128Gb/die Led Settings Activity LED Polarity : 1 (Inverted) Fault LED Polarity : 1 (Inverted) LED Blink Rate : 0 (250ms) Power Managment Settings Power Management Version : 2 (B01) Active State Power Mode : 0 (Default) DIPM Behavior in Active State : 0 (Default) HIPM Behavior in Active State : 0 (Default) Auto Idle Enable : 0 (Default) Idle State Power Mode : 0 (Default) DIPM Behavior in Idle State : 0 (Default) HIPM Behavior in Idle State : 0 (Default) Standby State Power Mode : 0 (Default) DIPM Behavior in Standby State : 0 (Default) HIPM Behavior in Standby State : 0 (Default) Sleep State Power Mode : 0 (Default) DIPM Behavior in Sleep State : 0 (Default) HIPM Behavior in Sleep State : 0 (Default) Auto slumber timer : 0 CMU power down : 0 (Default) Dual-align BIST Feature : 0 (Default) Temperature Sensor Settings Sensor 1: Device ID : 0 (Default) Device Address : 0 Max Temperature Threshold Level 1 Entry Point (MT1) : 0 Max Temperature Threshold Level 2 Entry Point (MT2) : 0 Min Temperature Threshold (LT1) : 0 Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default) Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default) Min Temperature Threshold Behavior (LT1B) : 0 (Default) Max Temperature Threshold Level 1 Return Point (MTR1): 0 Sensor 2: Device ID : 0 (Default) Device Address : 0 Max Temperature Threshold Level 1 Entry Point (MT1) : 0 Max Temperature Threshold Level 2 Entry Point (MT2) : 0 Min Temperature Threshold (LT1) : 0 Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default) Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default) Min Temperature Threshold Behavior (LT1B) : 0 (Default) Max Temperature Threshold Level 1 Return Point (MTR1): 0 Security Erase Options Security Erase Behavior : 0 (Default) Enhanced Security Erase Behavior (Military Erase) : 0 (Default) SATA Command and Firmware Options Flush Cache Behavior : 1 (Enable Checkpoint) ATA Security Set Enable : 0 (Default) Spread Spectrum Clocking Enable : 0 (Default) SATA Link Handling on Reboot : 0 (Default) ACS2 Support : 0 (Default) Failed Secure Unlock Delay Enable : 0 (Default(No delay)) Seek Complete in Error Status : 0 (Default) Read Long with Retry and without Retry : 0 (Default) Read Sectors without Retry : 0 (Default) Write DMA without Retry : 0 (Default) Write Long with Retry and without Retry : 0 (Default) Max SATA Link Rate : 2 (3 GBs) Deterministic Trim Setting : 0 (Default) Controller Drive Strength Rate : 0 (Default) PHY Setting : 0 (Default) Controller Slew Rate : 0 (Default) Put SIG FIS Delay : 0 (Default) Set Multiple Handling : 0 (Default) TRIM Timer Abort : 0 (Enable(Default)) Trim Support/Setting Word 169 Bit 0 : 0 (Default(Firmware default setting)) RDD1 Optimization : 0 (Default) Security Unlock Drive : 0 (Default(Compare Master Password)) Power Throttling Options Average Power Level 0-100 : 0 Maximum Power Level 0-100 : 0 Power Throttling Upon Unsafe Shutdown : 0 (Default) Dynamic Read Scrub Read Scrub Enabled : 0 (Default (Enabled)) Dynamic Read Scrub End Range1 : 0 Dynamic Read Scrub Rate Range1 : 0 Dynamic Read Scrub End Range2 : 0 Dynamic Read Scrub Rate Range2 : 0 Dynamic Read Scrub End Range3 : 0 Dynamic Read Scrub Rate Range3 : 0 Dynamic Read Scrub End Range4 : 0 Dynamic Read Scrub Rate Range4 : 0 Low Level Format Settings Max LBA Count for 512B Sectors : 937703088 Max LBA Count for 512B Plus DIFF Sectors : 0 Max LBA Count for 520B Sectors : 0 Max LBA Count for 524B : 0 Max LBA Count for 528B : 0 Max LBA Count for 4096 Sectors : 0 Max LBA Count for 4096 Plus DIFF Sectors : 0 Host Protected Area Host Protected Access : 0 (Always Reset HPA State On COMRESET) End of Life Behavior Enable End of Life : 0 (Default (EOL Enabled)) EOL Threshold 1 Type : 0 (Default (SSD Life Left)) EOL Threshold 1 Percentage : 0 EOL Threshold 1 Behavior : 0 (Default (Light Write Throttling)) EOL Threshold 2 Type : 0 (Default (SSD Life Left)) EOL Threshold 1 Percentage : 0 EOL Threshold 1 Behavior : 0 (Default (Heavy Write Throttling)) CDU Smart settings: defined 1 attributes ## Attr IntId Tresh Flag 00 0xbe 0x12 0 0x00 Fab Defect list entry : 36 Idx Bus CE Die Plane Block Lane3210 Defects 0 0 3 0 0 15 _B__ 1 1 0 0 0 0 45 BBBB 4 2 1 0 0 0 45 BBBB 4 3 0 0 0 1 45 BBBB 4 4 1 0 0 1 45 BBBB 4 5 0 1 0 0 45 BBBB 4 6 1 1 0 0 45 BBBB 4 7 0 1 0 1 45 BBBB 4 8 1 1 0 1 45 BBBB 4 9 0 2 0 0 45 BBBB 4 10 1 2 0 0 45 BBBB 4 11 0 2 0 1 45 BBBB 4 12 1 2 0 1 45 BBBB 4 13 1 3 0 0 45 BBBB 4 14 0 3 0 0 45 BBBB 4 15 1 3 0 1 45 BBBB 4 16 0 3 0 1 45 BBBB 4 17 0 3 0 0 116 _B__ 1 18 0 0 0 0 263 BBBB 4 19 1 0 0 0 263 BBBB 4 20 0 0 0 1 263 BBBB 4 21 1 0 0 1 263 BBBB 4 22 0 1 0 0 263 BBBB 4 23 1 1 0 0 263 BBBB 4 24 0 1 0 1 263 BBBB 4 25 1 1 0 1 263 BBBB 4 26 0 2 0 0 263 BBBB 4 27 1 2 0 0 263 BBBB 4 28 0 2 0 1 263 BBBB 4 29 1 2 0 1 263 BBBB 4 30 0 3 0 0 263 BBBB 4 31 1 3 0 0 263 BBBB 4 32 0 3 0 1 263 BBBB 4 33 1 3 0 1 263 BBBB 4 34 0 3 0 1 746 __B_ 1 35 0 3 0 0 1013 ___B 1 Fab Defects : 132 User Defect list entry: 0 Panic Dumps : 0 Panic Dumps list: Idx Accurev SyncCode UnlockLevel Size DataSize EPA Log Ok CRC Ok 0 -1 0xffffffff 0xffffffff -1 -1 0x00080002 0x0000 0x0000 1 -1 0xffffffff 0xffffffff -1 -1 0x20080002 0x0000 0x0000 2 -1 0xffffffff 0xffffffff -1 -1 0x00080102 0x0000 0x0000 3 -1 0xffffffff 0xffffffff -1 -1 0x20080102 0x0000 0x0000 MST settings not exist. MST result not exits. | Всего записей: 75 | Зарегистр. 22-04-2010 | Отправлено: 10:24 19-10-2018 | Исправлено: speedboy, 14:30 19-10-2018 |
|